Royer R-122 MKII

$1,795.00

Phantom Powered Active Ribbon Microphone

Finance Now
SKU: R-122 MKII Categories: , Brand:

Description

R-122 MKll Active Ribbon Microphone

The R-122 MKII ribbon microphone continues in the lineage of our original R-122, the world’s first phantom-powered active ribbon™ microphone. It delivers all of the warm, natural tone of our R-121, but with 13 dB more output, a switchable -15 dB pad.  A switchable bass cut, and impedance matching circuitry that makes it compatible with virtually any mic preamplifier.

The Pad

The R-122 MKll’s switchable -15 dB pad is positioned before the microphone’s electronics and, when engaged, eliminates any potential for headroom-related distortion on even the loudest sound sources. Wide open electric guitars are no problem. With the pad in, the R-122 MKll’s output is actually 2 dB lower than our flagship R-121.

The R-122 MKll’s well-designed pad has no sonic imprint. Once levels are matched, the R-122 MKll reproduces sound exactly the same with the pad in as with the pad out.

The Bass Cut

When switched in, the R-122 MKll’s bass cut starts filtering at 100 Hz, 6 dB per octave, effectively reducing the mic’s bass buildup due to proximity effect. This smooth filter is extremely useful on vocals, many acoustic instruments, and close-miked electric guitars when less bottom end is desired.

The R-122 MKll’s electronics are hand-wired in our Burbank, CA factory. The microphone utilizes a special Royer-designed toroidal transformer that delivers a faster transient response then traditional ribbons, making it a first call ribbon mic for drum overheads, percussion and all acoustic instruments.

Gain

Conventional ribbon microphones need high-quality, high-gain microphone preamplifiers to record softer sound sources. The R-122 MKll’s output level is much higher, allowing you to use practically any mic preamplifier or board pre’s to record even the quietest sounds. The R-122 MKll contains a fully balanced, hand-wired, discrete head amplifier system utilizing a specially wound toroidal transformer and ultra-low noise FET’s. This system is extremely quiet and brings the R-122 MKll’s sensitivity to 37 dB, all while allowing for high SPL recording! Go ahead and plug a MKll into any preamp with average gain – you’ll get full Royer performance and enough level to drive any recording medium.

There is no increase in self-noise in the R-122 MKll’s higher sensitivity. All of the mic’s additional output comes from its large, specially wound toroidal transformer – that wonderful thing called “free gain.” The phantom powered circuitry provides impedance conversion only, adding no noise of its own.

Impedance Matching

The R-122 MK’s active electronics put a perfect load on the ribbon element at all times, allowing the microphone to deliver its full sonic potential regardless of the input characteristics of the following pre. Due to its low-impedance output, R-122’s can be used on extremely long cable runs with minimal signal loss. In addition, the ribbon element can’t be damaged by phantom power, mis-wired cables or electrical glitches.

Patented Offset Ribbon Technology

The R-122’s proprietary offset ribbon transducer (Patent # 6,434,252) positions the ribbon element closer to the front (logo) side of the microphone. This configuration gives the ribbon more room to move within the prime magnetic field while maintaining full frequency response during high SPL recordings. It’s an integral piece of the magic of all Royer R-series microphones.

 

Technical:

  • Acoustic Operating Principle: Electrodynamic pressure gradient with active
    electronics.
  • Polar Pattern: Figure-8
  • Generating Element: 2.5-micron aluminum ribbon
  • Magnets: Rare Earth Neodymium
  • Frequency Response: 30 – 15,000 Hz ±3 dB
  • Sensitivity: -36 dB (re. 1v/pa ±1 dB)
  • Switchable Pad: -15 dB
  • Switchable Bass Cut: 100 Hz (6 dB per octave)
  • Self-Noise: < 18 dB
  • Output Impedance: 200 Ohms, balanced
  • Output Connector: Male XLR 3-pin (Pin 2 Hot)
  • Rated Load Impedance: 1K-Ohm minimum
  • Maximum SPL: 135 dB @ 30 Hz
  • Power Requirements: 48-Volt Phantom Only
  • Supply Current: 4 mA
  • Dimensions: 206mm L X 25mm W (8 1/8” L X 1” W)
  • Weight: 309 grams (10.9 oz)
  • Finish: Burnished Satin Nickel / Matte Black
    Chrome (optional)
  • Accessories: Protective wood case, mic sock
    Optional Accessories: Wind screen, shock mount
  • Microphone Warranty: Lifetime to original owner (repair or replace
    at Royer’s option)
  • Ribbon Element Warranty: One Year

Polar Pattern

polar pattern

Frequency Response

Additional information

Weight 4 kg
Options

, , ,